Ultra Start Automobile Alarm 1271M User Manual

REV.2006.03  
OWNER’S GUIDE  
MANUAL TRANSMISSION ONLY!  
Warning!!  
CARBON MONOXIDE MAY CAUSE SERIOUS INJURY, EVEN DEATH!  
It is the sole responsibility of the user to place the system in Service Mode  
when parking in an enclosed area ex: garage, partially enclosed area  
ex: carport, or when the vehicle is being serviced.  
NEVER INSTALL IN AN AUTO TRANSMISSION VEHICLE!!!  
 
PAGE 3  
OWNER’S GUIDE  
This Guide Covers The Following Systems:  
1271M - 2271M - 3266M - 3271M - 4266M - 4271M.  
About Ultra Start  
It is our continuing objective to design and manufacture the absolute  
best Remote Car Starters, Vehicle Security Systems, Keyless Entry  
Systems and Security Bypass units available in today’s competitive  
market. This objective is met by utilizing installation professionals with  
decades of industry experience to assist in each step of the design  
process. This has allowed us to build products that are very installer  
and user friendly yet offer advanced and innovative features. Our  
systems utilize intelligent programming and auto learning systems  
and are designed to work properly in every vehicle. Our systems are  
also designed wherever possible to be easily enhanced, allowing the  
consumer and the retailer to enjoy easy and cost effective upgrades  
and additions to their system down the road. Our limited lifetime  
warranty provides one of the best protection plans in the industry,  
giving both the consumer and the retailer confidence when they  
invest in an Ultra Start product.  
Feature List  
- Remote Keyless Entry.  
- Engine Idle Mode.  
- Anti-Grind Protection.  
- Ignition Auto Locks.  
- Turbo Timer Mode.  
- Starter Disable.  
- Car Finder.  
- Panic Mode. (Personal Protection)  
- System Override Protection.(Service Mode) - Safety Start Mode.*  
- Park Light Diagnostics.  
- Window Roll-up.  
- Up to 4 Different Transmitter Codes.  
- Built in Dual Stage Shock Sensor.**  
- Timer Mode (3 Different Start Intervals)  
- Multi Tone Siren.**  
*12xx/22xx MODELS ONLY  
**22xx/42xx MODELS ONLY  
PLEASE READ THIS MANUAL IN DETAIL.  
 
OWNER’S GUIDE  
PAGE 4  
Safety  
VERY IMPORTANT SAFETY NOTES!  
The owner/user MUST INSTALL a CARBON MONOXIDE  
DETECTOR in the living area near to where the vehicle is  
being stored or parked. It is the sole responsibility of the  
owner/user to keep the remote transmitters away from the  
reach of children and handle with care so that the system  
does not unintentionally start. When the vehicle is parked in  
an enclosed/partially enclosed area (ex: garage, car port...),  
being serviced (ex: oil change) or the vehicle is loaned to an  
operator not familiar with a remote starter,  
the system MUST BE placed Service Mode (see page 10).  
NEVER OPERATE THE SYSTEM IN AN  
ENCLOSED/PARTIALLY ENCLOSED AREA!  
 
PAGE 5  
OWNER’S GUIDE  
= 1  
= 2  
= 3  
= 4  
2-WAY LED  
2-WAY LCD  
 
OWNER’S GUIDE  
PAGE 6  
Remote Starter Functions  
Remote Starting (if remote start fails to start see page 19)  
1. Press and release the button.  
2. The park lights will flash and the siren* or horn (optional) will chirp once to  
confirm. The vehicle will then remote start, the siren* or horn (optional) will  
chirp and the park lights will then flash four times then remain on while the  
vehicle is running**.  
Important! If your vehicle is equipped MANUAL TRANSMISSION see your  
dealer IMMEDIATELY to have the correct model installed!!!  
Extended Run Time  
1. While the vehicle is running with the remote starter, press and release  
the button.  
2. The park lights will flash and the siren* or horn (optional) will chirp one time  
to confirm. The system will reset the run time**.  
NOTE: Not available with 4 minute run time.  
Remote Stop  
1. While the vehicle is running with the remote starter, press and hold  
the button for three seconds. The remote starter will shut down.  
2.The park lights will flash and the siren* or horn (optional) will chirp 2 times to  
confirm shutdown.  
NOTE: Pressing the brake pedal or opening the hood will also shut down the  
remote starter.  
Idle Mode  
1.While the vehicle is running with key, press and release the button.  
2.The park lights will turn on and the siren* or horn (optional) will chirp twice.  
3.Turn the ignition key to the “OFF” position and the vehicle will remain  
running**.  
Turbo Timer Mode  
1. While the vehicle is running with key, press the button.  
2. The park lights will turn on and the siren* or horn (optional) will chirp twice.  
3. Turn the ignition key off and the vehicle will continue to run for approximately  
2 minutes.  
*Alarm series ONLY!  
**Default 15 minutes.  
 
PAGE 7  
OWNER’S GUIDE  
Reservation Mode  
Very Important! Do not set Reservation Mode if the vehicle is occupied.  
Manual transmission remote starters must be set into Reservation Mode before  
the remote starter will activate. The activation type of Reservation Mode is  
determined when the system is installed.  
Auto Reservation Mode (Default)  
Step 1 - While the vehicle is running, place into neutral and apply the park brake.  
Step 2* - Press and release the brake pedal twice. The park lights will flash twice,  
the siren or horn (opt.) will chirp twice and the doors will unlock (opt.).  
Step 3 - Turn the ignition key off and the vehicle will continue running.  
Step 4** - Within 30 seconds, exit the vehicle and close all the doors. The vehicle will  
then shut off .  
Manual Reservation Mode (Optional)  
Step 1 - While the vehicle is running with the key, place transmission into neutral  
and apply the park brake.  
Step 2 - Press and release the button. The park lights will flash twice, the siren  
or horn (opt.) will chirp twice and the doors will unlock (opt.).  
Step 3 - Turn the ignition key off and the vehicle will continue running.  
Step 4 - Exit the vehicle and close all the doors.  
Step 5** - Press and hold the button for 3 seconds, the vehicle will then shut off.  
*
If the park lights do not flash and stay on or the siren (horn optional) chirps a third  
time, repeat Step 2.  
** If the vehicle has dome light delay, the vehicle may stay running until the dome  
light turns off. This is normally no longer than 30 seconds.  
THE VEHICLE MAY NOW BE SAFELY REMOTE STARTED.  
(See page 6 for Remote Starter Functions.)  
If Reservation Mode is not set, the remote starter will not activate. When the  
button is pressed the park lights will flash 4 times. 4 flashes is the diagnostic  
code for “Not in Reservation Mode”  
NOTE: Reservation Mode will reset if the doors of the vehicle are opened. To re-enter  
the vehicle without canceling the Reservation Mode (ex: forgot something..)  
The vehicle must first be remote started. While the vehicle is running by the  
remote starter the door may be opened. When done in the vehicle, close the  
door and remotely stop the vehicle by pressing and holding the button.  
 
OWNER’S GUIDE  
PAGE 8  
Remote Transmitter Functions  
Arm/ Lock (optional)  
1. Press and release the button.  
2. The park lights will flash and the siren* or horn (optional) will chirp one time.  
3. The system will arm and doors will lock (optional).  
NOTE: The LEDs on the antenna will start flashing within five seconds.  
If installed, the starter disable will activate.  
Disarm/ Lock (optional)  
1.Press and release the button on the remote transmitter.  
2.The park lights will flash and the siren* or horn (optional) will chirp two times.  
3.The system will disarm and doors will unlock (optional).  
NOTE: The LEDs on the antenna will stop flashing. If installed, the starter  
disable will deactivate.  
Silent Arm/Disarm  
1. Press and release the and buttons simultaneously.  
a) If the doors are in the locked position: The park lights will flash two times  
to confirm the doors have unlocked, without siren* chirps or horn honks.  
b) If the doors are in the unlocked position: The park lights will flash one  
time to confirm the doors have locked, without siren* chirps or horn honks.  
Constant Lock (optional)  
1. Press and release, then press and hold the button.  
2. The doors will lock. The park lights will flash and the siren* or horn (optional)  
will chirp one time.  
3. The lock output from the system will stay active until the button is released.  
NOTE: This feature can be used on select vehicles to roll up the power  
windows or to close a power sunroof.  
*Alarm series ONLY!  
 
PAGE 9  
OWNER’S GUIDE  
Remote Transmitter Functions  
Trunk (default button)  
1. Press and hold the button.  
2. The doors will unlock (optional), continue holding until the Trunk Release  
activates. The trunk release will be confirmed by one park light flash and  
siren*** or horn (optional) chirp.  
Trunk (optional button*)  
1. Press and hold the button.  
2. The doors will unlock (optional), continue holding until the Trunk Release  
activates. The trunk release will be confirmed by one park light flash and  
siren*** or horn (optional) chirp.  
NOTE: The trunk release output will stay active for 5 seconds as long as the  
or buttons are pressed. This feature may be used to roll down power  
windows or to open a power sunroof on select vehicles.  
IMPORTANT: The trunk release output will not activate when the ignition key is  
in the “ON” position.  
or  
Car Finder (default setting)**  
1. Press and hold the button for 3 seconds.  
2. The park lights will flash and the siren*** or horn (optional) will honk 5 times.  
NOTE: This feature can be used to locate the vehicle in a crowded parking lot.  
Panic  
1. Press and hold the button.  
2. The park lights will flash and the siren*** or horn (optional) will sound.  
3. Press and release the or the button to deactivate.  
NOTE: Panic will be active for 60 seconds or until deactivated by the remote  
transmitter.  
*1270 and 2270 series ONLY.  
**Not available on the 3265 and 4265 series.  
***Alarm series ONLY!  
 
OWNER’S GUIDE  
PAGE 10  
Timer Mode  
Timer Mode will start the vehicle at a user selectable start interval. The vehicle  
can be set to start once every 2, 3 or 4 hours, for a maximum of 12 starts. The  
vehicle will start at the selected start interval and run for the programmed  
runtime*.  
EXAMPLE: If the 4 hour start cycle was selected, the vehicle will start once  
every 4 hours and run for the programmed runtime*.  
To Enter Timer Mode.  
Method 1- Press and release the button, then press and hold the button  
for 6 seconds or until park lights turn on.  
Method 2 - Press the and buttons at the same time for 3 seconds or until  
the park lights will turn on.  
While the park lights are on the start cycle may be selected.  
2 hours  
3 hours  
4 hours  
Press and release the button  
Press and release the button  
Press and release the button  
2 Park light flashes  
3 Park light flashes  
4 Park light flashes  
NOTE: Timer Mode must be set each time the user wishes to use this feature.  
To Cancel Timer Mode  
Method 1- Press and release the button, then press and hold the button  
for 6 seconds.  
Method 2- Press the and buttons at the same time for 3 seconds.  
NOTE: Pressing the brake pedal or turning the ignition to the ON position will  
cancel Timer Mode. Cancellation will be confirmed with 2 park light  
flashes and 2 siren or horn (optional) chirps.  
IMPORTANT: Never remote start or set the Timer Mode if the vehicle  
is parked in a Garage or Attached Carport! (see page 4 SAFETY)  
*Default 15 minutes  
 
PAGE 11  
OWNER’S GUIDE  
Remote Transmitter Learn  
IMPORTANT! All remote transmitters not programmed at this time  
will be erased from memory for security.  
STEP 1 - Within 3 seconds turn the ignition key to the “ON”  
position three times leaving “ON” the third time.  
STEP 2 - Press and hold the Program Button. The park lights will  
turn “ON” and the siren or horn (optional) will chirp  
once. Continue to hold the Program Button,  
the park lights will turn “OFF” and the siren or  
horn (optional) will chirp 5 times quickly.  
NOTE: If the parking lights do not turn “ON”, release the Program Button and  
turn the ignition to the “OFF” position, wait 5sec and repeat steps 1 & 2.  
STEP 3a (Default) - While holding the Program Button, press and  
release the button on each of the remote  
transmitters to be programmed.  
STEP 3b (PadLoc/ - While holding the Program Button, press and  
2nd Car)* release the button on each of the remote  
transmitters to be programmed.  
PadLoc* is a safety feature that “LOCKS” the remote transmitter. To  
UNLOCK” the remote transmitter the button must be  
pressed simultaneously with the function chosen.  
or  
2nd Car* function allows the operation of two Ultra Start systems  
(in two separate vehicles) with one remote transmitter.  
Example: Press and release and simultaneously to remote start.  
NOTE: Some features not available with PadLoc* or 2nd car* mode.  
*12xx and 22xx series ONLY  
 
OWNER’S GUIDE  
PAGE 12  
System Service Mode (Valet Mode)  
System Service Mode will disable the remote starter. This will only effect the  
remote start portion of the system. The optional lock, unlock and trunk release  
features will still be operational. When the vehicle is to have any under hood or  
service work done, the system must be placed into Service Mode. This feature  
may also be used if a transmitter is lost, damaged or if the system malfunctions.  
ENTERING SERVICE MODE  
1. Turn the ignition key to the ON position, DO NOT START!  
2. Within 4 seconds, press and hold the Program Button (located on the  
antenna) for 5 seconds or until the siren/ horn (optional) chirps five times.  
NOTE: With the ignition key in the OFF position, the LEDs on the antenna will  
turn on solid to confirm Service Mode. If the button is pressed while  
the system is in Service Mode the park lights will flash 3 times slowly.  
EXITING SERVICE MODE  
1. Turn the ignition key to the ON position, DO NOT START!  
2. Within 4 seconds, press and hold the Program Button (located on the  
antenna) for 5 seconds or until the siren/ horn (optional) chirps two times.  
NOTE: With the ignition key in the OFF position, the LEDs on the Antenna will  
turn off and the remote starter functions will be re-enabled.  
5sec  
ATTENTION:  
TO AVOID SERIOUS INJURY, this remote start system must be set into  
Service Mode before any under hood servicing is started. Service Mode  
will prevent the vehicle from starting while the vehicle is being serviced.  
It is the sole responsibility of the vehicle’s owner to place the system into  
Service Mode. The manufacture accepts no responsibility for accidental  
starting of the vehicle while the vehicle is being serviced.  
 
PAGE 13  
OWNER’S GUIDE  
LCD DISPLAY 3265/4265 series  
These icon’s display the current status of the system. The icons may not all be  
present on the screen at all times, certain icons will only turn on when a feature  
is activated.  
STATUS ICON’S  
PROGRAMMABLE ICON’S  
STATUS CHECK MODE  
This feature is used to check the status of the system. To check the status  
press and release button on the remote transmitter. The remote will display  
the icons of the active features on the LCD screen.  
ANTENNA ICON- This icon is always visible. A series of lines  
next to the icon will appear whenever the remote transmitter is  
within transmitting range of the vehicle. The lines will disappear when  
out of transmitting range.  
KEY ICON- This icon will be displayed when the remote starter has  
been activated.  
SIREN ICON*- This icon will be displayed when the alarm has been  
triggered. The icon will stay displayed until the or the button is  
pressed.  
TRUNK ICON- This icon will be displayed when the trunk release is  
activated. The icon will stay displayed until the or the button is  
pressed.  
BATTERY ICON- This icon is always present to indicate the current  
battery level of the remote transmitter. The black area of the icon will  
disappear as the battery level decreases.  
TIMER ICON- This icon is displayed when the timer/cold start mode is  
activated.  
*42xx Series ONLY  
 
OWNER’S GUIDE  
PAGE 14  
LCD DISPLAY 3265/4265 series  
RUN TIMER- This icon activates during remote starting. The bar graph will  
count down in 2 minute increments, indicating how much time is left on the  
remote starter’s runtime.  
NOTE: At rest four bars will scan back and fourth.  
EXHAUST and WHEEL’S- These icons activate during remote starting.  
They will stay on during the runtime countdown.  
LOCK ICON- This icon indicates the ARMED status of the system.  
NOTE: The doors will be locked (optional) and the LEDs on the antenna will be  
flashing.  
UNLOCK ICON - This icon indicates the DISARMED status of the system.  
NOTE: The doors will be unlocked (optional) and the LEDs on the antenna will  
be off.  
 
PAGE 15  
OWNER’S GUIDE  
LCD DISPLAY 3265/4265 series  
TRUNK ICON- This icon indicates that the trunk has been opened.  
SIREN and LOCK ICONS*- These icons indicate that the alarm has been  
triggered by the door, hood or ignition inputs.  
SIREN and HAMMER ICONS*- These icons indicate that the alarm has  
been triggered by the shock sensor input.  
*4265 Series ONLY  
 
OWNER’S GUIDE  
PAGE 16  
LCD DISPLAY 3265/4265 series  
Setting The Time  
Press and hold the and buttons until the remote transmitter chimes and the  
minute portion of the clock begins to flash.  
To change from minutes to hours, press and release the button.  
To increase the minutes or hours, press and release the button.  
To decrease the minutes or hours, press and release the button.  
Press and release the button to exit or the remote transmitter will exit if there  
is no activity for 20 seconds.  
NOTE: To set the AM/ PM icon, continue changing the hour until the  
appropriate icon is displayed.  
To Enter User Program Mode  
1. Press and hold the button for three seconds. The icon will begin to  
flash, the system is now in User Program Mode.  
2. Press and release the button to scroll the list of programmable icons.  
Selected feature icon will begin to flash.  
3a. Press the button to turn the feature icon OFF.  
3b. Press the button to turn the feature icon ON.  
4. Press the button to exit program mode and save settings.  
*If the remote is not used for 20 seconds the system will exit Program  
Mode.  
 
PAGE 17  
OWNER’S GUIDE  
LCD DISPLAY 3265/4265 series  
Programable Icons-The six squares found at the bottom of the  
display are user/dealer programmable (see page 16 to enter).  
TIMER ICON- When the vehicle starts in Timer Mode, this icon will  
appear in conjunction with the usual icons that indicate that the vehicle  
is running by the remote starter.  
TELEPHONE ICON- N/A  
KEY ICON- This icon is displayed if the ignition key is in the “ON” position or if  
the system detected a start fault.  
NOTE: The start fault must be corrected before the remote starter will activate  
again (see page 19 for diagnostic codes).  
NUMBER ICON- This icon is displayed to indicate First car or Second  
car remote transmitter operations.  
SIREN ICON- If the icon is displayed, the siren will work normally. If  
the icon is not displayed, the siren delete feature is ON and the siren will  
not be active if a button is pressed on the remote transmitter.  
NOTE: Panic and car finder will still be active.  
SHOCK SENSOR ICON*- If this icon is displayed the shock sensor  
is active. If this icon is not displayed the shock sensor is OFF.  
SERVICE MODE ICON- This icon indicates the status of the Service  
Mode feature. If this icon is present, the system is in Service Mode.  
NOTE: In Service Mode, keyless entry and optional features will still  
function.  
?
*4265 series ONLY  
 
OWNER’S GUIDE  
PAGE 18  
Shock Sensor-Alarm series ONLY!  
Shock Sensor Programming/ Adjustment  
To enter shock sensor programming:  
Press and hold the and the buttons for three seconds.  
The park lights will flash and the siren will three times.  
While the park lights are “ON”, strike the vehicle with the amount of force  
wanted to trigger the alarm.  
NOTE: The siren will chirp 3 times each time the system detects impact.  
Adjusting the shock sensor:  
Press and release to increase sensitivity (up to 10 chirps/ flashes).  
Press and release to decrease sensitivity (down to 1 chirp/ flash).  
NOTE: Be careful not to impact the vehicle in a area that may cause damage.  
The most common location for testing and setting the shock sensor is  
the vehicles A-pillar. The A-Pillar is the metal support that runs from the  
roof of the vehicle to the hood area.  
To exit and save shock sensor programming:  
Press and hold the and the buttons, the siren will chirp and the park lights  
will flash the number of times of the shock sensor impact level chosen.  
Example: Level 5 = 5 Chirps/ 5 Park Light flashes  
IMPORTANT SECURITY NOTES!  
If the system has been triggered (shock sensor, door input..), the siren  
will sound for approximately 60 seconds. Press and release the or  
the button to silence the siren (the system will remain armed).  
Press and hold the button to disarm the system. The siren and park  
lights will flash three times to indicate the system had been triggered.  
 
PAGE 19  
OWNER’S GUIDE  
Diagnostics  
If the remote starter does not activate when the button is pressed the park  
lights will flash a diagnostic code to indicate what shutdown input has been  
triggered.  
PARK LIGHTS  
3 Slow Flashes  
4 Slow Flashes  
5 Slow Flashes  
5 Flashes  
STATUS LED  
LED’s On Solid  
DIAGNOSTIC CODE  
System Is In Service Mode  
Not in Reservation Mode (M units)  
Ignition On During Start Attempt  
Hood Pin Opened  
Brake Pedal Shutdown  
Tach Lock-Out(see dealer)  
Series of 4 Flashes  
Series of 5 Flashes  
Series of 5 Flashes  
Series of 6 Flashes  
Series of 7 Flashes  
6 Flashes  
7 Flashes  
Battery Replacement  
The transmitter battery should be changed at least once every year to maintain  
proper operating range. Replace with a quality 23A 12volt Alkaline battery  
(OE remote). Replace with two quality 3V lithium batteries (XR remote).  
Replace with a quality 1.5V battery (2-way).  
Test remote for  
proper operation.  
Remove the top  
case, then replace  
the battery.  
Replace top case  
and Re-install  
screw.  
Carefully remove  
the screw from the  
back of the remote.  
S
A
e
S
A
e
e
S
w
o
A
e
e
S
e
o
S
T
n
e
w
o
T
S
T
n
w
r
e
s
n
r
s
g
e
u
g
u
i
2
-
r
s
d
e
2
-
g
u
ie  
i
d
2
-
e
f
o
d
w
f
o
r
m
w
f
o
r
m
o
r
w
r
a
m
o
r
e
a
y
o
r
e
i
n
a
y
f
o
e
i
n
y
fra  
oo  
r
m
ifr  
n
o
m
a
t
m
a
t
in  
o
t
in  
o
i
o
n
 
OWNER’S GUIDE  
PAGE 20  
Limited Lifetime Warranty  
The manufacturer warrants to the original purchaser of their remote starters and alarms, that the product shall  
be free from defects in material and workmanship. However, should this product be proven to be defective,  
within a two year period from the original date of purchase, the manufacturer will, without charge to the  
purchaser (excluding any charges incurred to have the product delivered to the manufacturer), repair or replace  
any part of the remote starter and/or alarm which the manufacturer agrees to be defective. After the initial 2  
year period the manufacture shall repair or replace defective products with a nominal processing fee of $30.00  
USD. All warranties apply to the original purchaser and the vehicle in which it was originally installed ONLY.  
Repairs or replacement of defective modules shall remain at the discretion of the manufacturer. All other parts,  
components, accessories and/or optional equipment pertaining to the remote starter and alarm are not  
included in the manufacturer’s warranty. This warranty is non-transferable. Request for warranty service  
from any Factory Authorized Dealer must be accompanied with the original purchase receipt or have  
product registered by authorized dealer on manufacturer’s website. Failure to comply with any of these  
conditions may result in warranty being voided. This warranty does not cover the following: removal and  
reinstall labor charges, shipping charges, abuse, misuse, or accidental damages to the remote starter and  
alarm, automobile, and/or parts there of. This warranty is void upon modification, repairs, or alterations of any  
part of the product. The manufacturer does not guarantee or insure against theft of the vehicle or its contents.  
Alarm models are designed only to act as a deterrent against possible theft. This alarm may qualify for auto  
insurance discounts, contact your Insurance Agent for further information . The manufacturer shall not be held  
liable for any consequential damages due to breach of this or any other warranty, expressed, or implied. This  
warranty gives you specific legal rights. Your specific legal rights may vary for each region.  
CERTAIN DAMAGES EXCLUDED  
-
The manufacturer expressly disclaims any liability or responsibility for  
incidental damages caused by the product, including economic loss, loss of use of the product, car rentals, or  
any other costs relating to the care and custody of the product. The manufacturer disclaims liability or  
responsibility for any consequential damages caused by the product or resulting from its use, including the cost  
of repairing or replacing other property damaged by the product or caused by its use, whether or not the  
product is working properly. The product is intended to deter unauthorized use of the vehicles in which it is  
installed. The manufacturer does not warrant that the product is fool-safe against theft and/or vandalism and/or  
human error or misuse. The manufacturer accepts no liability or responsibility for any damage of any kind  
whatsoever caused to any vehicle in which the product is installed or any resulting damage from its use. The  
manufacturer accepts no responsibility or liability for any damage resulting to or theft of the vehicle or its  
contents, caused or alleged to be caused, directly or indirectly, by failure of the product.  
MANUAL TRANSMISSION STARTERS the installation of a remote starter MUST only be done with a  
FCC Notice  
specified manual transmission starter. It is the sole responsibility of the vehicles operator to insure  
that the vehicle is left with the transmission in neutral position when the remote starter is in use. The  
This device complies with Part 15 of the FCC rules. Operation of this device is subject to the following  
manual transmission starter is designed to be an added measure of safety ONLY! The manufacturer  
conditions:  
(1) This device may not cause harmful interference, and  
does not guarantee or insure against any damages or loss of life that could result in the event of a  
(2) This device must accept any interference received, including interference that may cause undesired  
operation.  
remote starter starting while the vehicle is in gear. Manual transmission models are designed only to  
act as a deterrent against the vehicle starting in gear, this is the vehicle’s owner’s and operator’s  
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance  
r
v
e
o
s
id  
p
s
o
t
h
s
e
ib  
u
i
s
li  
e
tyrs  
authority to operate this device.  
.
 

Texas Instruments Projection Television 8100CB User Manual
Toshiba Air Conditioner RAS 10JKCVP User Manual
Toshiba Projection Television 56MX195 User Manual
Tricity Bendix Cooktop SI 251 User Manual
Tripp Lite Power Supply APSINT3636VR User Manual
Uniden Two Way Radio GMR1058 2CK4CK User Manual
Vintage Gas Grill VBQ 56 User Manual
Vizio TV Mount XMF1000 User Manual
VTech Telephone VT 4121 User Manual
Weber Water Heater 98642 User Manual