Ultra Start Automobile Alarm 430 Series User Manual

INSTALL GUIDE  
430 and 440 Series Vehicle Security Systems  
WWW.ULTRASTARTERS.COM  
Technical Support
FCC/ID Notice  
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:  
(1) This device may not cause harmful interference, and  
(2) This device must accept any interference received, including interference that may cause  
undesired operation.  
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance  
void the user’s authority to operate this devise.  
 
WIRING DIAGRAM  
*500ma negative output  
Orange  
Gray  
(-) When Armed  
*500ma negative output  
Trunk Release  
Ignition Input  
Yellow  
Red  
Connect to vehicles ignition wire  
Connect to constant power. 20amp input  
Connect to Siren wire. 2amp Maximum  
Connect to chassis ground  
12 Volt Input  
Brown  
Black  
Siren Output  
Ground Input  
Door Input  
Purple  
Green  
Blue  
Connect to door pin. (+) when opened  
Connect to door pin. (-) when opened  
Connect to hood and / or trunk pin  
Door Input  
Hood Input  
 
10 Pin Connector  
White  
Orange  
Grey  
Yellow  
RedMain  
Brown  
Black  
Purple  
Green  
Blue  
(+) Park lights  
Park light output.  
(-) When Armed  
(-) Trunk Release  
Ignition Input  
Power Input  
(+) Siren Output  
Ground Input  
(+) Door Input  
(-) Door Input  
(-) Hood Input  
Negative output when system is armed.  
Negative output for trunk release. 500ma max.  
Input from vehicles ignition wire.  
Constant 12 Volt input.  
Positive output for siren.  
System ground input.  
Positive door pin switch input.  
Negative door pin switch input.  
Negative input from hood pin switch.  
3 Pin Connector Red  
Green  
Door Lock  
Door Lock Output - *Programmable  
12 Volt Output Output for voltage inverter. Low Current Only  
Blue Door Unlock Door Unlock Output - *Programmable  
Recommended Installation Procedures  
Mounting the module- Never mount the module in the engine compartment. Select a  
location under the dash to install the main module. Be certain that the module is securely  
attached and does not obstruct any serviceable areas. Mount the module so that it cannot  
be seen if looking under the dash as it could be easily unplugged by a thief. The module  
must be free from all moving parts.  
Installing the LED- Choose a location that will be highly visible when the LED is installed.  
Most vehicles are equipped with knock out panels in the dashboard, these panels are easily  
removable and can be easily replaced if necessary. Once the location is picked, use drill bit  
and drill a hole through the panel. Test fit the LED into the hole. Plug the Led into the Red  
connector on the main module.  
Installing the Program Button- Choose a location to mount the Program Button. This  
location should be hidden and not visible from outside the vehicle. Once the location of the  
switch is picked, use a 1/4” drill bit and drill a hole. Remove the nut and push the Program  
Button through the hole. Replace the nut and tighten until the switch is secure. Plug the  
Program Button into the Blue connector of the main module.  
Under Hood Connections- Route the hood pin (optional) and Siren wire through the  
firewall, into the engine compartment. Always try to pull the wires through a factory rubber  
grommet. If drilling through the firewall, BE CAREFUL. Check for obstructions on both sides  
of the firewall. After drilling use a snap in grommet to protect the wires from sharp edges.  
Mounting the Siren- Choose a location in the engine compartment that is away from  
high heat sources and direct exposer to water. The siren should be mounted as well as  
grounded to solid metal. Run the wiring for the siren so that it can not be seen or reached  
from below the vehicle.  
 
BASIC INSTALLATION  
Step 1 - Connect All Of the Following Wires  
10 Pin Power Connector  
Black  
Yellow  
Red  
Ground Input  
Ignition Input  
Power Input  
System ground input.  
Input from vehicles ignition wire.  
Constant 12 Volt input.  
Brown  
White  
Green*  
Purple*  
(+) Siren Output Positive output for siren.  
(+) Park lights  
(-) Door Input  
(+) Door Input  
Positive park light output.  
Negative door pin switch input.  
Positive door pin switch input.  
*Test for door pin type (+ or -) then connect the appropriate wire (Green or Purple)  
Step 2- Plug-In The Module  
When all the connections are done, the control module can be plugged in. Before  
connecting the control module, make sure the ignition is in the OFF position. Plug in the  
main harness then any other connectors that were used.  
Step 3- Test And Adjust The Shock Sensor  
To test the Shock Sensor.  
1. Press the Lock button once to arm the system.  
2. Wait five seconds then impact the vehicle. Lighter impacts to the vehicle should trigger  
the warn away (The siren will chirp three times). A harder impact to the vehicle will trigger  
the full alarm.(The siren will activate for 60 seconds then turn off).  
3. To deactivate the alarm when triggered, press the unlock button twice.  
To Increase The Sensitivity.  
Turn the adjustment screw Clockwise 1/4 turn then re-test the sensitivity. Repeat this  
procedure until the sensitivity of the system is at the appropriate level.  
** Do not set to sensitive.  
To Decrease The Sensitivity.  
Turn the adjustment screw Counter Clockwise 1/4 turn then re-test the sensitivity. Repeat  
this procedure until the sensitivity of the system is at the appropriate level.  
Step 4- Test The System  
1. Open all the vehicles windows.  
2. Press the Lock button to arm the system.  
3. Wait five seconds (or until the dome light goes out) then reach in through a window and  
open the door. The alarm will then activate (repeat on all the doors).  
4. Test the Shock Sensor again and adjust if necessary.  
5. Insure that all additional features are working as intended.  
6. If necessary proceed to Program Mode to adjust the programmable outputs.  
Your Basic Install Is Complete!  
 
PROGRAM OVERVIEW  
Program mode allows you to adjust the settings and options of your system. Your system  
has been intelligently designed by installers with years of experience. The system’s default  
settings do not require any program changes in most cases. However, this system does  
incorporate a advanced programming system with settings that can be easily adjusted  
Entering Program Mode  
To Enter Program Mode  
1) Make sure ignition is in the off position.  
2) Within three seconds turn the key ON the OFF.  
3) Press and release the Program Button two times.  
4) The siren will chirp and the lights will flash once to confirm entering Program Mode.  
Note: If unit does not enter Program Mode, turn ignition off and repeat steps 1-3.  
** The ignition wire(Yellow) MUST be connected. If it is not connected it will not be possible  
to enter the Program Modes.  
Changing A Programmable Setting  
1) Enter Program Mode As explained above.  
2) When in program Mode, change the desired Program Setting by pressing the  
transmitter buttons in the following sequences.  
***The Systems Default Setting Are Shown In Bold Lettering.  
Quick View Programming  
Programmable Feature  
Shock Sensor Status  
Arm / Disarm Chirps  
Ignition Auto Locks  
Door Lock Pulse Length  
Double Pulse Unlock  
Door Input / Voltage Sense  
Passive / Active Locks  
Passive / Active Arming  
System Reset  
Press Buttons  
#3-#3-#1  
#2-#1-#1  
#1-#3-#2  
#1-#3-#1  
#2-#2-#1  
#1-#1-#3  
#3-#2-#2  
#1-#2-#3  
#3-#3-#3  
One Chirp  
Disabled  
Chirps Off  
Off  
3 Second  
Two Pulses Single Pulses  
Voltage  
Active  
Active  
Two Chirps  
Enabled  
Chirps On  
On  
.75 Second  
Door Pin  
Passive  
Passive  
Confirmed by Three Siren Chirps  
System Reset  
This feature will reset the module to it’s factory programmed default setting. This feature  
will not delete transmitter codes from memory.  
To Reset The System To Factory Defaults.  
1) Turn the ignition key On then Off.  
2) Press the Program Button two times. The system will respond with two siren chirps.  
3) Press the transmitter buttons in the following order: #3-#3-#3. The system will respond  
with three siren chirps to confirm the system has been re-set to factory defaults.  
 
Enter Program Mode  
Entering program mode is done by the following steps:  
1) Make sure ignition is in the off position.  
2) Turn the ignition key ON - OFF, leaving key in the OFF position.  
3) Press and release the Valet button two times.  
4) The siren will chirp one time to confirm entering program mode.  
( If this does not happen, turn ignition off, wait five seconds and repeat steps 1-4).  
Passive / Active Arming  
To change settings:  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#1 - #2 then #3  
3 - The siren will respond with the following:  
1 Chirp Active Arming  
2 Chirps Passive Arming  
Repeat sequence to change selection  
Passive / Active Arming  
To change settings:  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#3 - #3 then #2  
3 - The siren will respond with the following:  
1 Chirp Active Locks  
2 Chirps Passive Locks  
Repeat sequence to change selection  
Door Lock Timing  
To change settings:  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#1 - #3 then #1  
3 - The siren will respond with the following:  
1 Chirp 3 Second Door Locks  
2 Chirps 0.75sec Pulses  
Repeat sequence to change selection  
Ignition Auto Locks  
To change settings:  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#1 - #3 then #2.  
3 - The siren will respond with the following:  
1 Chirp  
2 Chirps  
Auto Lock Disabled  
Auto Lock Enabled  
Repeat sequence to change selection  
 
Double Pulse Unlock  
To change settings:  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#2 - #2 then #1.  
3 - The siren will respond with the following:  
1 Chirp  
Double Pulse Unlock  
2 Chirps  
Single Pulse Unlock  
Repeat sequence to change selection  
Voltage / Door Pin Sensing  
To change settings:  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#1 - #1 then #3  
3 - The siren will respond with the following:  
1 Chirp  
2 Chirps  
Voltage Sensing- No Door Pin Connection Needed  
Door Pin- Door Pin Connection Required  
Repeat sequence to change selection  
Chirp Delete  
To change settings:  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#2 - #2 then #1  
3 - The siren will respond with the following:  
1 Chirp  
Chirps Disabled  
2 Chirps  
Chirps Enabled  
Repeat sequence to change selection  
Shock Sensor Disable  
To change settings:  
1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times)  
2 - Press & release transmitter buttons in the following sequence  
#3 - #3 then #1  
3 - The siren will respond with the following:  
1 Chirp  
2 Chirps  
Shock Sensor OFF  
Shock Sensor ON  
Repeat sequence to change selection  
 
Transmitter Programming  
Follow the steps below to program the transmitters to the system s memory  
Step 1 - Turn the Ignition key ON then OFF - Leaving Key Off.  
Step 2 - Press and release the Program Button twice then press and hold.  
Step 3 - The siren will respond with five chirps to confirm Transmitter Program Mode.  
Note: If the siren does not respond, repeat Steps1&2  
Step 4 - Continue to hold the Program Button and press lock button on each of the  
transmitter’s to be programmed(Maximum of 3 Different transmitter codes).  
Step 5 - The system will respond with a siren chirp each time a transmitter is programmed.  
Exit - After five seconds the system will exit transmitter program mode automatically.  
NOTE: You must program ALL of the transmitters to be used at one time. For the owner’s  
security any transmitters not programmed at this time will be erased from memory.  
*** This system will store a maximum of three transmitter codes in memory.  
Deleting Transmitters  
Follow the steps below to permanently delete a transmitter code from the system s memory.  
Step 1 - Turn the Ignition key ON then OFF - Leaving Key Off.  
Step 2 - Press and release the Program Button twice then press and hold.  
Step 3 - The siren will respond with five chirps to confirm Transmitter Program Mode.  
Note: If the siren does not respond, repeat Steps1&2  
Step 4 - Continue to hold the Program Button and press lock button on only the transmitters  
that are intended for use on the system.(*Maximum of 3 Different transmitter codes).  
Step 5 - The system will respond with a siren chirp each time a transmitter is programmed.  
Exit - After five seconds the system will exit transmitter program mode automatically.  
All previous transmitter code are now deleted from the systems memory.  
Basic Transmitter Functions  
Button #1- Press and release to arm the alarm and lock the doors.  
- Press and hold to activate Panic mode.  
- Press and release to deactivate triggered alarm.  
#1  
#3  
#2  
#1 #2  
Button #2- Press and release to disarm and unlock the doors.  
- Press and hold to activate the Trunk Release.  
- Press and release to deactivate triggered alarm.  
#3  
Button #3- Press and hold to activate the Car Finder Mode.  
 
Lock Doors & Arm The Alarm  
1.Press & release the LOCK button on the remote transmitter.  
2.The park lights will flash and the siren will chirp once.  
3.The doors will lock.  
4.The LED will start flashing within five seconds.  
Unlock Doors & Disarm The Alarm  
1.Press & release the UNLOCK button on the remote transmitter.  
2.The park lights will flash and the siren will chirp twice.  
3.The doors will unlock.  
4.The LED will stop flashing.  
Silent Arm And Disarm  
1.Press & release the button three, then press & release the lock or unlock button.  
2.If the doors are locked this will unlock the doors without siren chirps, the park  
lights will flash two times to confirm the doors have unlocked.  
3.If the doors are unlocked this will lock the doors without siren chirps, the park  
lights will flash one time to confirm they have locked.  
Trunk Release  
1.Press and hold the UNLOCK button for three seconds.  
2.The doors will unlock, continue holding the unlock button three seconds. the  
Trunk release will then activate. The trunk release will be confirmed by one  
park light flash.  
3 sec.  
3.For safety reasons, the trunk release output will not activate when ignition  
key is in the “On” po si tion .  
Car Finder Mode  
1. Press and hold the button for two seconds.  
2. The system will flash the park lights and chirp the siren five times.  
**This feature can help find your vehicle in a crowded parking lot.  
Panic Mode  
1.Press & hold the LOCK button for three seconds.  
2.The park lights will flash and the siren will activate.  
PANIC MODE DISABLE  
1. Press LOCK button to disable the panic mode and to lock the doors.  
2. Press UNLOCK button to disable the panic mode and unlock the doors.  
3. Panic Mode will stay activated until disabled by the remote transmitter.  
 
Service Mode  
1. The system must be disarmed and the ignition is turned OFF.  
2.Press and release the lock and unlock buttons at the same time, then press  
and hold the lock button for five seconds.  
3.The system will respond with five chirps and park light flashes to confirm  
that the system is in Valet mode.  
4. The LED will stay ON steady to confirm Valet Mode.  
Exit Service Mode  
1.Press and release the lock and unlock buttons at the same time, then press  
and hold the lock button for five seconds.  
2.The system will respond with two chirps and park light flashes to confirm that  
the system has exited Valet mode.  
3. The LED will turn OFF.  
Note: If the LED does not turn off, check that all the door’s are closed. The LED  
stays On solid when a door is left opened.  
Emergency Service Mode  
Emergency Service Mode temporarily disables the alarm system. This feature  
can be used if the remote is lost or if the system malfunctions.  
ENTERING VALET MODE  
1.While the ignition is “On” press and hold the Service button for five seconds.  
The siren will chirps five times.  
2.Alarm functions will be disabled and the LED will be ON steady. The door-locks  
and trunk release are still operational.  
EXITING VALET MODE  
1.While the ignition is “On”press and hold the Service button for five seconds.  
The siren will chirps two times.  
2. The system returns to normal operation.  
Starter Disable  
The system has an optional starter disable output that can be connected by your  
dealer. When the starter disable relay is installed and connected to the system,  
the vehicle’s starter will be disabled when the system is armed.  
To activate the starter disable press the lock button on the remote. The system  
will arm and the starter will no longer operate.  
To deactivate the starter disable, press the unlock button and the LEDS will stop  
flashing and the starter will be re-enabled.  
 
Negative Type Door Locks  
Positive Type Door Locks  
87  
87a  
87  
87a  
86  
86  
85  
85  
30  
30  
5 Wire / Reverse Polarity Type Door Locks  
87  
87a  
87  
87a  
86  
86  
85  
85  
30  
30  
Negative Park Lights- In some cases the park lights may flash erratically after  
installing the negative park light relay. To correct this issue add a diode between the coil  
pins of the relay as shown.  
Ground  
Add IN4001 Diode  
as shown  
87  
87a  
86  
85  
White  
30  
Negative park light output  
 

Thermos Gas Grill 465611003 User Manual
Tiger Games 70 138 User Manual
Topcom Cordless Telephone BUTLER 1800T User Manual
Topfield TV Receiver TF 7000 HD PVRt User Manual
Toshiba DVD Player D R4 User Manual
Uniden Bluetooth Headset r035 User Manual
Uniden Cordless Telephone TRU9585 User Manual
Universal Remote Control Universal Remote UR5U 9000L User Manual
Vector Battery Charger VEC021STC User Manual
Weed Eater Lawn Mower 159757 User Manual